Thin Film Coating Technician - ROTATING SHIFT

Coherent•Saxonburg, PA

1d•Onsite

About The Position

Primary Duties & Responsibilities Operation of thin film coating and test equipment including: Retrieving proper designs according to set schedule and programs into coating system operations controller Operate coating equipment according to set parameter and establishing procedures Determine evaporation layer end points to high level of accuracy By observation and deduction, extract the maximum amount of data from each coating run and document accordingly Monitor two high volume coating chambers at one time, while supporting peers in their operations Communicate daily activities during quality meetings Operate characterization/test equipment and interpret results Maintain schedule demands and requirements Coating Chamber Setup Evaluate design requirements and prepare evaporation materials accordingly Evaluate evaporation components to assure proper operation requirements Change out all worn/dirty components and replace with cleaned or new ones Observe and extract the maximum amount of data from each calibration/production run. Evaluate data from calibration/production runs Use calibration equipment to assure proper setup and quality control Double check design and run requirements before loading run Document log information required for design operations Accept responsibility for the quality of the thin film coating process and equipment assigned Related Job Tasks Supporting cleaning area in loading of optical components Prepare evaporation material according to procedure Maintain inventory controls Perform minor maintenance with minimal support Take traces between coating runs to verify performance Learn nonstandard system operations at a basic level Audit personal and peer procedures for process consistency Support senior operators in the training of new employees Provide engineering support with timely, accurate information Attend and participate in daily quality meetings

Requirements

High school graduate or equivalent
Able to work in a demanding, fast-paced production environment
Able to multi-task and prioritize
Forward thinker
Strong attention to detail and quality
Team-oriented; works well with others in the group
Excellent interpersonal skills
Good communication, both verbal and nonverbal
Must be able to effectively listen and assimilate, present organized trains of thought, assure a timely information exchange with others as required
Must be able to work with acids, radioactive materials and other toxic chemicals
Make-up and perfumes discouraged while working in clean room to prevent contamination
Long periods of standing and/or walking (3+ hours at a time)
Must be able to wear a full-face respirator. Must be clean shaven
Must be able to lift, push, pull up to 50 lbs.
Bending and stooping required
May need to utilize step stool or elevated working platform to adjust within coating chamber and to disassemble/reassemble
All employees are required to follow the site EHS procedures and Coherent Corp. Corporate EHS standards
This position is subject to a pre-employment physical evaluation associated with wearing a respirator
This position must under-go annual physical evaluations associated with respirator use

Nice To Haves

Manufacturing experience preferred

Responsibilities

Operation of thin film coating and test equipment
Retrieving proper designs according to set schedule and programs into coating system operations controller
Operate coating equipment according to set parameter and establishing procedures
Determine evaporation layer end points to high level of accuracy
Extract the maximum amount of data from each coating run and document accordingly
Monitor two high volume coating chambers at one time, while supporting peers in their operations
Communicate daily activities during quality meetings
Operate characterization/test equipment and interpret results
Maintain schedule demands and requirements
Evaluate design requirements and prepare evaporation materials accordingly
Evaluate evaporation components to assure proper operation requirements
Change out all worn/dirty components and replace with cleaned or new ones
Observe and extract the maximum amount of data from each calibration/production run
Evaluate data from calibration/production runs
Use calibration equipment to assure proper setup and quality control
Double check design and run requirements before loading run
Document log information required for design operations
Accept responsibility for the quality of the thin film coating process and equipment assigned
Supporting cleaning area in loading of optical components
Prepare evaporation material according to procedure
Maintain inventory controls
Perform minor maintenance with minimal support
Take traces between coating runs to verify performance
Learn nonstandard system operations at a basic level
Audit personal and peer procedures for process consistency
Support senior operators in the training of new employees
Provide engineering support with timely, accurate information
Attend and participate in daily quality meetings
execution and maintenance of the ISO 9000, 9001, 14001 and/or other applicable standards that may apply to the relevant roles and responsibilities within the Quality Management System and Environmental Management System
Ensure adherence to company’s values (ICARE) in all aspects of your position at Coherent Corp.